|
 |
 |
|
 |
● Description
The MVX 84 VGA A is an 8x4 VGA is designed to route high resolution computer-video and stereo audio signals. Convenient 15-pin HD connectors are used for all computer-video input and output connections. Unbalanced stereo audio is input on 3.5 mm stereo mini jacks, while balanced or unbalanced stereo audio is output on captive screw connectors. Using pre-terminated cable assemblies, such as Extron's VGA with Audio Cables, eliminates crimping and makes installations faster and easier.
In addition, the MVX 84 VGA A comes standard with the QuickSwitch Front Panel Controller (QS-FPC™), which allows for touch-of-a-button input and output selection directly from the front panel. It can also be controlled through RS-232 serial control utilizing Extron's Simple Instruction Set (SIS™) commands, the optional IR 501 remote control, or with the Extron MCP 1000 control panel or MKP 1000 control keypad.
● Features
- 300 MHz (-3 dB) RGB video bandwidth, fully loaded — Ensures flawless switching and distribution of signals without signal degradation. The MVX matrix switchers provide 300 MHz (-3dB) of RGB video bandwidth at full performance capacity when one input signal drives all outputs.
- Triple Action Switching™ (RGB delay) — RGB delay blanks the screen when the matrix switcher switches to a new source. The new sync signals precede the RGB signals, so there is no glitch during the transition.
- Balanced and unbalanced audio output — Balanced or unbalanced stereo audio signals are output on captive screw connectors.
- Audio input gain and attenuation — Allows users to set the level of audio gain or attenuation (-18dB to +10dB). Individual input audio levels may be adjusted so there are no noticeable volume differences when switching between sources. This can be accomplished via the front panel controls or RS-232 serial remote.
- Audio breakaway — Provides the capability to break away an audio signal from its corresponding video signal. Audio breakaway switching can be accomplished via the front panel controls or RS-232 serial remote.
- Switchable audio output levels — Output levels can be switched between professional (+4dBu) and consumer levels (-10dBV). This feature is available via RS-232 serial control only and allows users to utilize a mix of professional and consumer-level equipment.
- View I/O mode — Available via the front panel and RS-232 serial control, users can easily view which individual inputs and outputs are actively connected.
- Global presets — Individual I/O configurations may be saved and recalled either from the QuickSwitch front panel or through the serial controls. This time-saving feature allows you to set up I/O configurations and keep them in memory for future use.
- Front panel security lockout — Ideal for unsecured environments, this feature locks out all front panel functions; however, these same functions are available through RS-232 serial control.
- Downloadable firmware updates — The latest firmware can be conveniently downloaded from the Extron Web site. Updates for new features and capabilities can be easily upgraded through the RS-232 serial port.
- QuickSwitch Front Panel Controller (QS-FPC™) — Allows for touch-of-a-button input and output selection.
- RS-232 serial control — The MVX Series offer RS-232 serial control, allowing the switcher to be controlled via a third party control system using Extron's Simple Instruction Set (SIS™).
- Simple Instruction Set (SIS) — Extron's SIS is a set of basic ASCII code commands that provide simple control through a control system. Instead of programming in long, obscure strings of code, the SIS makes it easy to operate an Extron product using RS-232 control.
- Control software — For serial remote control from a PC, Extron ships Windows®-based control software with every matrix switcher. This icon-driven software uses a graphical, drag-and-drop interface to make I/O configuration and other customization functions simple and convenient. This software also offers an emulation mode for configuration of an off-site matrix switcher; the I/O configuration may then be saved for future downloading to the matrix switcher.
- Optional MCP 1000 and MKP 1000 control — Utilizing the MCP 1000 master control panel, and any combination of MCP 1000 control panels or MKP 1000 control keypads, offer the flexibility to control a MVX matrix switcher from a remote location or room. Both remote control options are easy to use and provide tactile buttons for quick selection. Each MCP 1000 panel may be used for one-button switching of a particular output and selecting global presets. Each MKP 1000 keypad may be used to select a different input or preset.
- IR remote control — Basic operation of any MVX matrix switcher can be performed via the optional IR 501 remote control.
● Specifications
| MVX VGA A Series Matrix Switchers |
|
| Video |
| Routing |
|
| MVX 44 VGA A |
4 x 4 matrix |
| MVX 48 VGA A |
4 x 8 matrix |
| MVX 84 VGA A |
8 x 4 matrix |
| MVX 88 VGA A |
8 x 8 matrix |
| Gain |
Unity |
| Bandwidth |
300 MHz (-3 dB), fully loaded |
| Crosstalk |
<-60 dB nominal @ 10 MHz, <-39 dB @ 100 MHz |
| Switching speed |
20 ms (max.) |
|
| Video input |
| Number/signal type |
|
| MVX 44/48 VGA A |
4 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level sync), S-video, composite video |
| MVX 84/88 VGA A |
8 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level sync), S-video, composite video |
| Connectors |
|
| MVX 44/48 VGA A |
4 female 15-pin HD |
| MVX 84/88 VGA A |
8 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for R-Y and B-Y of component video, and for C of S-video |
| Minimum/maximum levels |
Analog: 0.3 V to 1.5 Vp-p with no offset at unity gain |
| Impedance |
75 ohms |
| Horizontal frequency |
15 kHz to 145 kHz |
| Vertical frequency |
30 Hz to 170 Hz |
| Return loss |
<-40 dB @ 5 MHz |
| DC offset (max. allowable) |
1.5 V |
|
| Video output |
| Number/signal type |
|
| MVX 44/84 VGA A |
4 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level sync), S-video, composite video |
| MVX 48/88 VGA A |
8 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs, component video (bi-level and tri-level sync), S-video, composite video |
| Connectors |
|
| MVX 44/84 VGA A |
4 female 15-pin HD |
| MVX 48/88 VGA A |
8 female 15-pin HD |
| Nominal level |
1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for R-Y and B-Y of component video, and for C of S-video |
| Minimum/maximum levels |
0.3 V to 1.5 Vp-p (follows input) |
| Impedance |
75 ohms |
| Return loss |
<-40 dB @ 5 MHz |
| DC offset |
<20 mV with input at 0 offset |
| Switching type |
Triple-Action™ |
|
| Sync |
| Input type |
RGBHV, RGBS, RGsB, RsGsBs |
| Output type |
RGBHV, RGBS, RGsB, RsGsBs (follows input) |
| Standards |
Computer scan rates and also NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level |
0.5 V to 5.0 Vp-p |
| Output level |
TTL: 5.0 Vp-p, unterminated |
| Input impedance |
510 ohms |
| Output impedance |
75 ohms |
| Max. propagation delay |
Horizontal: 90 ns nominal
Vertical: 160 ns nominal |
| Max. rise/fall time |
4 ns |
| Polarity |
Positive or negative (follows input) |
|
| Audio |
| Routing |
|
| MVX 44 VGA A |
4 x 4 stereo matrix |
| MVX 48 VGA A |
4 x 8 stereo matrix |
| MVX 84 VGA A |
8 x 4 stereo matrix |
| MVX 88 VGA A |
8 x 8 stereo matrix |
| Throughput gain |
Adjustable. At default (when input gain is set to 0 dB and output level is set to "Pro"), overall gain is 12 dB for balanced output. The gain range is -6 dB to +22 dB for balanced output when the output level is set to "Pro". |
| Frequency response |
20 Hz to 20 kHz, ±0.2 dB |
| THD + Noise |
0.05% @ 1 kHz, 0.3 % @ 20 kHz at nominal level |
| S/N |
>90 dB at maximum output (unweighted) |
| Crosstalk |
<-65 dB @ 20 kHz, <-80 dB @ 1 kHz or below 60 Hz |
| Stereo channel separation |
>80 dB @ 1 kHz, >55 dB @ 20 Hz to 20 kHz |
|
| Audio input |
| Number/signal type |
|
| MVX 44/48 VGA A |
4 stereo, unbalanced |
| MVX 84/88 VGA A |
8 stereo, unbalanced |
| Connectors |
|
| MVX 44/48 VGA A |
4 female 3.5 mm stereo mini jacks: tip (L), ring (R), sleeve (GND) |
| MVX 84/88 VGA A |
8 female 3.5 mm stereo mini jacks: tip (L), ring (R), sleeve (GND) |
| Impedance |
>18k ohms unbalanced, DC coupled |
| Nominal level |
-10 dBV (316 mV) (default), but also compatible with +4 dBu (1.23 V), 0 dBu (0.775 V), ‑20 dBV (100 mV) |
| Maximum level |
>+12 dBV (4 V), (unbalanced) at 1%THD+N |
| Input gain |
–18 dB to +10 dB, adjustable per input; default = 0 dB. (this is referenced to the internal bus signal level. It can be verified by measuring the unbalanced output when the output level is set to "Consumer".) |
| NOTE |
|
0 dBu = 0.775 V, 0 dBV = 1 V, 0 dBV ≈ 2 dBu. | |
|
| Audio output |
| Output gain |
0 dB unbalanced (Consumer) or +12 dB balanced (Pro), selectable;
default = +12 dB, balanced, when output level is set to "Pro" |
| Number/signal type |
|
| MVX 44/84 VGA A |
4 stereo, balanced/unbalanced |
| MVX 48/88 VGA A |
8 stereo, balanced/unbalanced |
| Connectors |
|
| MVX 44/84 VGA A |
(4) 3.5 mm captive screw connectors, 5 pole |
| MVX 48/88 VGA A |
(8) 3.5 mm captive screw connectors, 5 pole |
| Impedance |
50 ohms unbalanced, 100 ohms balanced |
| Gain error |
±0.1 dB channel to channel |
| Nominal level |
+4 dBu (1.23 V) (default) balanced (Pro), or
-10 dBV (316 mV) unbalanced (Consumer), selectable |
| Maximum level (Hi-Z) |
>+22 dBu, balanced; >+14 dBV, unbalanced at 1%THD+N at default settings |
| Maximum level (600 ohm) |
>+20 dBu, balanced; >+12 dBV unbalanced at 1%THD+N at default settings |
|
| Control/remote — switcher |
| Serial control port |
RS-232, 9-pin female D connector |
| Baud rate and protocol |
9600, 8-bit, 1 stop bit, no parity |
| Control pin configurations |
2 = TX, 3 = RX, 5 = GND, 9 = hardwired IR input |
| IR controller module |
IR 501 (optional remote control) |
| Program control |
Extron's control/configuration program for Windows®
Extron's Simple Instruction Set (SIS™) |
|
| General |
| Power |
100 VAC to 240 VAC, 50/60 Hz, 30 watts, internal, autoswitchable |
| Temperature/humidity |
Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Rack mount |
Yes, with included brackets, part #70-077-03, or furniture mountable with an optional under-desk mounting bracket, part #70-222-01 |
| Enclosure type |
Metal |
| Enclosure dimensions |
1.75" H x 17.4" W x 8.5" D (1U high, full rack wide)
4.4 cm H x 44.2 cm W x 21.6 cm D
(Depth excludes connectors and knobs. Width excludes rack ears.) |
| Product weight |
7.0 lbs (3.2 kg) |
| Shipping weight |
10 lbs (5 kg) |
| Vibration |
ISTA 1A in carton (International Safe Transit Association) |
| Listings |
UL, CUL |
| Compliances |
CE, FCC Class A, VCCI, AS/NZS, ICES |
| MTBF |
30,000 hours |
| Warranty |
3 years parts and labor |
| NOTE |
|
All nominal levels are at ±10% | |
| NOTE |
|
Specifications are subject to change without notice. | |
|
|
 |
 |
|
|
|
|
|
|
|
|
)
